转让电话：13313028229联系我们
保定市模具模板制造有限公司
转让电话：13313028229
邮箱：
新闻动态
选择高速钢模具需要考虑的方面
高速钢模具/高速水泥制品材质加工要求
Material processing requirements of high speed steel mold / high speed cement products
高速钢模具除了要选用高品质的模具之外，对于材质的要求也是很高的，必须采用天然的麻石机经剥削加工而成，材质的强度也必须合格，表面不能有瑕疵，光滑，洁净，边角不得有缺角，无明显的色差，色斑，装卸时要轻，稳，慢以防磕碰损坏材料。高速钢模具必须选用一级钢板，内壁不得有凸起的小泡或凹进去的小坑，这样都会影响整个水泥制品的外形美观度。路牙石在加工时必须采用精确的仪器按照统一的标准进行下料，面对路边的一面必须采用抛光机，长宽误差允许在20mm。
In addition to selecting high-quality mold, the high-speed steel mold also has high requirements for material. It must be made of natural stone machine through exploitation and processing. The strength of the material must also be qualified. The surface must be free of defects, smooth and clean. The edges and corners must be free of missing angles, obvious color differences, and color spots. When loading and unloading, it should be light, stable and slow to prevent the material from being damaged by collision. The high-speed steel mould must be made of first-class steel plate, and the inner wall shall be free of convex bubbles or concave pits, which will affect the appearance of the whole cement product. During the processing of the curbstone, the precise instrument must be used for blanking according to the unified standard, and the polishing machine must be used for the side facing the roadside, with the length width error allowed to be 20 mm.
选择高速钢模具需要考虑的方面
Aspects to be considered in selecting high speed steel mould
1、整体厂家制作生产的水泥道牙钢模具是不是您图纸上所绘制的水泥路沿石钢模具的形状。
1. Is the cement road die made by the whole manufacturer the shape of the stone steel die along the cement road drawn on your drawing.
2、选材看看所制作水泥道牙钢模具的材料是不是您所要求的厚度与材料。接口检查每一个水泥3、道牙钢模具的焊接接口是不是存在问题。角铁角铁的选择是不是您要求的尺寸，还有厚度。
2. Material selection to see whether the material of the cement road teeth steel mold is the thickness and material you require. Interface check whether there is any problem in the welding interface of each cement 3 and road steel mold. The selection of angle iron is not the size you require, but also the thickness.
4、拆装测试拆装部件是不是适用，是否存在一些不好使用或者螺丝螺杆不配套等现象。
4. Disassembly and assembly test whether the disassembled parts are applicable, whether there are some problems such as difficult to use or screws and screws are not matched.
Material processing requirements of high speed steel mold / high speed cement products
高速钢模具除了要选用高品质的模具之外，对于材质的要求也是很高的，必须采用天然的麻石机经剥削加工而成，材质的强度也必须合格，表面不能有瑕疵，光滑，洁净，边角不得有缺角，无明显的色差，色斑，装卸时要轻，稳，慢以防磕碰损坏材料。高速钢模具必须选用一级钢板，内壁不得有凸起的小泡或凹进去的小坑，这样都会影响整个水泥制品的外形美观度。路牙石在加工时必须采用精确的仪器按照统一的标准进行下料，面对路边的一面必须采用抛光机，长宽误差允许在20mm。
In addition to selecting high-quality mold, the high-speed steel mold also has high requirements for material. It must be made of natural stone machine through exploitation and processing. The strength of the material must also be qualified. The surface must be free of defects, smooth and clean. The edges and corners must be free of missing angles, obvious color differences, and color spots. When loading and unloading, it should be light, stable and slow to prevent the material from being damaged by collision. The high-speed steel mould must be made of first-class steel plate, and the inner wall shall be free of convex bubbles or concave pits, which will affect the appearance of the whole cement product. During the processing of the curbstone, the precise instrument must be used for blanking according to the unified standard, and the polishing machine must be used for the side facing the roadside, with the length width error allowed to be 20 mm.
选择高速钢模具需要考虑的方面
Aspects to be considered in selecting high speed steel mould
1、整体厂家制作生产的水泥道牙钢模具是不是您图纸上所绘制的水泥路沿石钢模具的形状。
1. Is the cement road die made by the whole manufacturer the shape of the stone steel die along the cement road drawn on your drawing.
2、选材看看所制作水泥道牙钢模具的材料是不是您所要求的厚度与材料。接口检查每一个水泥3、道牙钢模具的焊接接口是不是存在问题。角铁角铁的选择是不是您要求的尺寸，还有厚度。
2. Material selection to see whether the material of the cement road teeth steel mold is the thickness and material you require. Interface check whether there is any problem in the welding interface of each cement 3 and road steel mold. The selection of angle iron is not the size you require, but also the thickness.
4、拆装测试拆装部件是不是适用，是否存在一些不好使用或者螺丝螺杆不配套等现象。
4. Disassembly and assembly test whether the disassembled parts are applicable, whether there are some problems such as difficult to use or screws and screws are not matched.
